Cisco Packet Tracer

Liberty University

CSIS 331

Lab 10 Instructions

***Please use the Topology and Instructions below to create a Packet Tracer from scratch. There will not be a Packet Tracer provided for you, you must create it new. If the routers do not have enough interfaces; you will need to go to the physical tab of the router and add the correct interface card to the existing router. Make sure the router is powered down while this is going on. Please reach out to your instructor if you have issues.***

Packet Tracer:

[Adapted from Cisco Networking Academy Routing and Switching 3.2.1.9]

Objectives

Configure and Verify RIPv2 Routing

Configure RIPv2 on the routers and verify that it is running.

Configure a passive interface.

Examine routing tables.

Disable automatic summarization.

Configure a default route.

Verify end-to-end connectivity.

Background / Scenario

RIP version 2 (RIPv2) is used for routing of IPv4 addresses in small networks. RIPv2 is a classless, distance-vector routing protocol, as defined by RFC 1723. Because RIPv2 is a classless routing protocol, subnet masks are included in the routing updates. By default, RIPv2 automatically summarizes networks at major network boundaries. When automatic summarization has been disabled, RIPv2 no longer summarizes networks to their classful address at boundary routers.

In this lab, you will configure the network topology with RIPv2 routing, disable automatic summarization, propagate a default route, and use CLI commands to display and verify RIP routing information.

Configure and Verify RIPv2 Routing

You will now configure RIPv2 routing on all routers in the network and then verify that the routing tables are updated correctly. After RIPv2 has been verified, you will disable automatic summarization, configure a default route, and verify end-to-end connectivity.

PCs are unable to ping each other.

a. Each workstation should be able to ping the attached router. Verify and troubleshoot if necessary.

b. The routers should be able to ping one another.

Step 1: Configure RIPv2 routing.

a. Configure RIPv2 on R1as the routing protocol and advertise the appropriate connected networks.

R1# config t

R1(config)# router rip

R1(config-router)# version 2

R1(config-router)# passive-interface g0/1

R1(config-router)# network 172.30.0.0

R1(config-router)# network 10.0.0.0

The passive-interface command stops routing updates out the specified interface. This process prevents unnecessary routing traffic on the LAN. However, the network that the specified interface belongs to is still advertised in routing updates that are sent out across other interfaces.

b. Configure RIPv2 on R3 and use the network statement to add the appropriate connected networks and prevent routing updates on the LAN interface.

c. Configure RIPv2 on R2 and use the network statements to add the appropriate connected networks. Do not advertise the 209.165.201.0 network.

Note: It is not necessary to make the G0/0 interface passive on R2 because the network associated with this interface is not being advertised.

Step 2: Examine the current state of the network.

a. The status of the two serial links can quickly be verified using the show ip interface brief command on R2.

R2# show ip interface brief

Interface IP-Address OK? Method Status Protocol

Embedded-Service-Engine0/0 unassigned YES unset administratively down down

GigabitEthernet0/0 209.165.201.1 YES manual up up

GigabitEthernet0/1 unassigned YES unset administratively down down

Serial0/0/0 10.1.1.2 YES manual up up

Serial0/0/1 10.2.2.2 YES manual up up

b. Check connectivity between PCs. List your finding in the ping table.

From PC-A, is it possible to ping PC-B? Why?

From PC-A, is it possible to ping PC-C? Why?

From PC-C, is it possible to ping PC-B? Why?

From PC-C, is it possible to ping PC-A? Why?

c. Verify that RIPv2 is running on the routers.

You can use the debug ip rip, show ip protocols, and show run commands to confirm that RIPv2 is running. The show ip protocols command output for R1 is shown below.

R1# show ip protocols

Routing Protocol is “rip”

Outgoing update filter list for all interfaces is not set

Incoming update filter list for all interfaces is not set

Sending updates every 30 seconds, next due in 7 seconds

Invalid after 180 seconds, hold down 180, flushed after 240

Redistributing: rip

Default version control: send version 2, receive 2

Interface Send Recv Triggered RIP Key-chain

Serial0/0/0 2 2

Automatic network summarization is in effect

Maximum path: 4

Routing for Networks:

10.0.0.0

172.30.0.0

Passive Interface(s):

GigabitEthernet0/1

Routing Information Sources:

Gateway Distance Last Update

10.1.1.2 120

Distance: (default is 120)

Answer question 1 on the Answer Sheet.

When you are finished observing the debugging outputs, issue the undebug all command at the privileged EXEC prompt.

Answer question 2 on the Answer Sheet.

d. Examine the automatic summarization of routes.

The LANs connected to R1 and R3 are composed of discontiguous networks. R2 displays two equal-cost paths to the 172.30.0.0/16 network in the routing table. R2 displays only the major classful network address of 172.30.0.0 and does not display any of the subnets for this network.

R2# show ip route

10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks

C 10.1.1.0/30 is directly connected, Serial0/0/0

L 10.1.1.2/32 is directly connected, Serial0/0/0

C 10.2.2.0/30 is directly connected, Serial0/0/1

L 10.2.2.2/32 is directly connected, Serial0/0/1

R 172.30.0.0/16 [120/1] via 10.2.2.1, 00:00:23, Serial0/00/1

[120/1] via 10.1.1.1, 00:00:09, Serial0/0/0

209.165.201.0/24 is variably subnetted, 2 subnets, 2 masks

C 209.165.201.0/24 is directly connected, GigabitEthernet0/0

L 209.165.201.1/32 is directly connected, GigabitEthernet0/0

R1 displays only its own subnet for the 172.30.10.0/24 network. R1 does not have a route for the 172.30.30.0/24 subnet on R3.

R1# show ip route

10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks

C 10.1.1.0/30 is directly connected, Serial0/0/0

L 10.1.1.1/32 is directly connected, Serial0/0/0

R 10.2.2.0/30 [120/1] via 10.1.1.2, 00:00:21, Serial0/0/0

172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks

C 172.30.10.0/24 is directly connected, GigabitEthernet0/1

L 172.30.10.1/32 is directly connected, GigabitEthernet0/1

R3 only displays its own subnet for the 172.30.30.0/24 network. R3 does not have a route for the 172.30.10.0/24 subnets on R1.

R3# show ip route

10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks

C 10.2.2.0/30 is directly connected, Serial0/0/1

L 10.2.2.1/32 is directly connected, Serial0/0/1

R 10.1.1.0/30 [120/1] via 10.2.2.2, 00:00:23, Serial0/0/1

172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks

C 172.30.30.0/24 is directly connected, GigabitEthernet0/1

L 172.30.30.1/32 is directly connected, GigabitEthernet0/1

Use the debug ip rip command on R2 to determine the routes received in the RIP updates from R3 and list it on Question 3 Answer Sheet.

R3 is not sending any of the 172.30.0.0 subnets, only the summarized route of 172.30.0.0/16, including the subnet mask. Therefore, the routing tables on R1 and R2 do not display the 172.30.0.0 subnets on R3.

Step 3: Disable automatic summarization.

a. The no auto-summary command is used to turn off automatic summarization in RIPv2. Disable auto summarization on all routers. The routers will no longer summarize routes at major classful network boundaries. R1 is shown here as an example.

R1(config)# router rip

R1(config-router)# no auto-summary

b. Issue the clear ip route * command to clear the routing table.

R1(config-router)# end

R1# clear ip route *

c. Examine the routing tables. Remember that it will take some time to converge the routing tables after clearing them.

The LAN subnets connected to R1 and R3 should now be included in all three routing tables.

R2# show ip route

Gateway of last resort is not set

10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks

C 10.1.1.0/30 is directly connected, Serial0/0/0

L 10.1.1.2/32 is directly connected, Serial0/0/0

C 10.2.2.0/30 is directly connected, Serial0/0/1

L 10.2.2.2/32 is directly connected, Serial0/0/1

172.30.0.0/16 is variably subnetted, 3 subnets, 2 masks

R 172.30.0.0/16 [120/1] via 10.2.2.1, 00:01:01, Serial0/0/1

[120/1] via 10.1.1.1, 00:01:15, Serial0/0/0

R 172.30.10.0/24 [120/1] via 10.1.1.1, 00:00:21, Serial0/0/0

R 172.30.30.0/24 [120/1] via 10.2.2.1, 00:00:04, Serial0/0/1

209.165.201.0/24 is variably subnetted, 2 subnets, 2 masks

C 209.165.201.0/24 is directly connected, GigabitEthernet0/0

L 209.165.201.1/32 is directly connected, GigabitEthernet0/0

R1# show ip route

Gateway of last resort is not set

10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks

C 10.1.1.0/30 is directly connected, Serial0/0/0

L 10.1.1.1/32 is directly connected, Serial0/0/0

R 10.2.2.0/30 [120/1] via 10.1.1.2, 00:00:12, Serial0/0/0

172.30.0.0/16 is variably subnetted, 3 subnets, 2 masks

C 172.30.10.0/24 is directly connected, GigabitEthernet0/1

L 172.30.10.1/32 is directly connected, GigabitEthernet0/1

R 172.30.30.0/24 [120/2] via 10.1.1.2, 00:00:12, Serial0/0/0

R3# show ip route

10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks

C 10.2.2.0/30 is directly connected, Serial0/0/1

L 10.2.2.1/32 is directly connected, Serial0/0/1

R 10.1.1.0/30 [120/1] via 10.2.2.2, 00:00:23, Serial0/0/1

172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks

C 172.30.30.0/24 is directly connected, GigabitEthernet0/1

L 172.30.30.1/32 is directly connected, GigabitEthernet0/1

R 172.30.10.0 [120/2] via 10.2.2.2, 00:00:16, Serial0/0/1

d. Use the debug ip rip command on R2 to examine the RIP updates.

R2# debug ip rip

After 60 seconds, issue the no debug ip rip command.

Answer Questions 4 and 5 on the Answer Sheet.

Step 4: Configure and redistribute a default route for Internet access.

a. From R2, create a static route to network 0.0.0.0 0.0.0.0, using the ip route command. This forwards any traffic with an unknown destination address to PC-B at 209.165.201.2, simulating the Internet by setting a Gateway of Last Resort on router R2.

R2(config)# ip route 0.0.0.0 0.0.0.0 209.165.201.2

b. R2 will advertise a route to the other routers if the default-information originate command is added to its RIP configuration.

R2(config)# router rip

R2(config-router)# default-information originate

Step 5: Verify the routing configuration.

a. View the routing table on R1.

R1# show ip route

Gateway of last resort is 10.1.1.2 to network 0.0.0.0

R* 0.0.0.0/0 [120/1] via 10.1.1.2, 00:00:13, Serial0/0/0

10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks

C 10.1.1.0/30 is directly connected, Serial0/0/0

L 10.1.1.1/32 is directly connected, Serial0/0/0

R 10.2.2.0/30 [120/1] via 10.1.1.2, 00:00:13, Serial0/0/0

172.30.0.0/16 is variably subnetted, 3 subnets, 2 masks

C 172.30.10.0/24 is directly connected, GigabitEthernet0/1

L 172.30.10.1/32 is directly connected, GigabitEthernet0/1

R 172.30.30.0/24 [120/2] via 10.1.1.2, 00:00:13, Serial0/0/0

Answer Question 6 on the Answer Sheet.

b. View the routing table on R2.

Answer Question 7 on the Answer Sheet.

Step 6: Verify connectivity.

a. Simulate sending traffic to the Internet by pinging from PC-A and PC-C to 209.165.201.2.

Answer Question 8 on the Answer Sheet.

b. Verify that hosts within the subnetted network can reach each other by pinging between PC-A and PC-C.

Answer Question 9 on the Answer Sheet.

Note: It may be necessary to disable the PCs firewall.

Answer the Reflection Questions 1 and 2 , Paste R1, R2 and R3 Output onto the Answer Sheet.

__MACOSX/Lab10/._Lab 10 Instructions(1).docx
Lab10/Lab 10 Answer Sheet-PLo.docx
Liberty University

CSIS 331

Lab 10 Answer Sheet

Ping From Device

Ping to Device IP

Possible Y/N

Why?

PC-A

PC-B

PC-A

PC-C

PC-B

PC-C

PC-A

1. When issuing the debug ip rip command on R2, what information is provided that confirms RIPv2 is running?

2. When issuing the show run command on R3, what information is provided that confirms RIPv2 is running?

3. Use the debug ip rip command on R2 to determine the routes received in the RIP updates from R3 and list them here.

4. What is the route in the RIP updates that is received from R3?

5. Are the subnet masks included in the routing updates? __ Yes / __ No

6. How can you tell from the routing table that the subnetted network shared by R1 and R3 has a pathway for Internet traffic?

7. How is the pathway for Internet traffic provided in its routing table?

8. Were the pings successful?__ Yes / __ No

9. Were the pings successful?__ __ Yes / __ No

Reflection Questions 1: Why would you turn off automatic summarization for RIPv2?

Reflection Questions 2:How did R1 and R3learn the pathway to the Internet?

Copy and Paste R1 show run Output:

Copy and Paste R2 show run Output:

Copy and Paste R3 show run Output:

__MACOSX/Lab10/._Lab 10 Answer Sheet-PLo.docx
Applied Sciences
Architecture and Design
Biology
Business & Finance
Chemistry
Computer Science
Geography
Geology
Education
Engineering
English
Environmental science
Spanish
Government
History
Human Resource Management
Information Systems
Law
Literature
Mathematics
Nursing
Physics
Political Science
Psychology
Reading
Science
Social Science
Home
Blog
Archive
Essay
Reviews
Contact
Copyright © 2019 HomeworkMarket.comHOMEWORKMARKET.COM YOUR HOMEWORK ANSWERSHomeworkMarket
chat0
Home.Homework Answers.
Help.
Log in / Sign up
Cisco Packet Tracer
profile
FamilyGuy007

Lab10.zip
Home>Computer Science homework help>Cisco Packet Tracer
Lab10/Lab 10 Instructions(1).docx
Liberty University

CSIS 331

Lab 10 Instructions

Packet Tracer:

[Adapted from Cisco Networking Academy Routing and Switching 3.2.1.9]

Objectives

Configure and Verify RIPv2 Routing

Configure RIPv2 on the routers and verify that it is running.

Configure a passive interface.

Examine routing tables.

Disable automatic summarization.

Configure a default route.

Verify end-to-end connectivity.

Background / Scenario

Configure and Verify RIPv2 Routing

PCs are unable to ping each other.

a. Each workstation should be able to ping the attached router. Verify and troubleshoot if necessary.

b. The routers should be able to ping one another.

Step 1: Configure RIPv2 routing.

a. Configure RIPv2 on R1as the routing protocol and advertise the appropriate connected networks.

R1# config t

R1(config)# router rip

R1(config-router)# version 2

R1(config-router)# passive-interface g0/1

R1(config-router)# network 172.30.0.0

R1(config-router)# network 10.0.0.0

b. Configure RIPv2 on R3 and use the network statement to add the appropriate connected networks and prevent routing updates on the LAN interface.

c. Configure RIPv2 on R2 and use the network statements to add the appropriate connected networks. Do not advertise the 209.165.201.0 network.

Note: It is not necessary to make the G0/0 interface passive on R2 because the network associated with this interface is not being advertised.

Step 2: Examine the current state of the network.

a. The status of the two serial links can quickly be verified using the show ip interface brief command on R2.

R2# show ip interface brief

Interface IP-Address OK? Method Status Protocol

Embedded-Service-Engine0/0 unassigned YES unset administratively down down

GigabitEthernet0/0 209.165.201.1 YES manual up up

GigabitEthernet0/1 unassigned YES unset administratively down down

Serial0/0/0 10.1.1.2 YES manual up up

Serial0/0/1 10.2.2.2 YES manual up up

b. Check connectivity between PCs. List your finding in the ping table.

From PC-A, is it possible to ping PC-B? Why?

From PC-A, is it possible to ping PC-C? Why?

From PC-C, is it possible to ping PC-B? Why?

From PC-C, is it possible to ping PC-A? Why?

c. Verify that RIPv2 is running on the routers.

You can use the debug ip rip, show ip protocols, and show run commands to confirm that RIPv2 is running. The show ip protocols command output for R1 is shown below.

R1# show ip protocols

Routing Protocol is “rip”

Outgoing update filter list for all interfaces is not set

Incoming update filter list for all interfaces is not set

Sending updates every 30 seconds, next due in 7 seconds

Invalid after 180 seconds, hold down 180, flushed after 240

Redistributing: rip

Default version control: send version 2, receive 2

Interface Send Recv Triggered RIP Key-chain

Serial0/0/0 2 2

Automatic network summarization is in effect

Maximum path: 4

Routing for Networks:

10.0.0.0

172.30.0.0

Passive Interface(s):

GigabitEthernet0/1

Routing Information Sources:

Gateway Distance Last Update

10.1.1.2 120

Distance: (default is 120)

Answer question 1 on the Answer Sheet.

When you are finished observing the debugging outputs, issue the undebug all command at the privileged EXEC prompt.

Answer question 2 on the Answer Sheet.

d. Examine the automatic summarization of routes.

R2# show ip route

10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks

C 10.1.1.0/30 is directly connected, Serial0/0/0

L 10.1.1.2/32 is directly connected, Serial0/0/0

C 10.2.2.0/30 is directly connected, Serial0/0/1

L 10.2.2.2/32 is directly connected, Serial0/0/1

R 172.30.0.0/16 [120/1] via 10.2.2.1, 00:00:23, Serial0/00/1

[120/1] via 10.1.1.1, 00:00:09, Serial0/0/0

209.165.201.0/24 is variably subnetted, 2 subnets, 2 masks

C 209.165.201.0/24 is directly connected, GigabitEthernet0/0

L 209.165.201.1/32 is directly connected, GigabitEthernet0/0

R1 displays only its own subnet for the 172.30.10.0/24 network. R1 does not have a route for the 172.30.30.0/24 subnet on R3.

R1# show ip route

10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks

C 10.1.1.0/30 is directly connected, Serial0/0/0

L 10.1.1.1/32 is directly connected, Serial0/0/0

R 10.2.2.0/30 [120/1] via 10.1.1.2, 00:00:21, Serial0/0/0

172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks

C 172.30.10.0/24 is directly connected, GigabitEthernet0/1

L 172.30.10.1/32 is directly connected, GigabitEthernet0/1

R3 only displays its own subnet for the 172.30.30.0/24 network. R3 does not have a route for the 172.30.10.0/24 subnets on R1.

R3# show ip route

10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks

C 10.2.2.0/30 is directly connected, Serial0/0/1

L 10.2.2.1/32 is directly connected, Serial0/0/1

R 10.1.1.0/30 [120/1] via 10.2.2.2, 00:00:23, Serial0/0/1

172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks

C 172.30.30.0/24 is directly connected, GigabitEthernet0/1

L 172.30.30.1/32 is directly connected, GigabitEthernet0/1

Use the debug ip rip command on R2 to determine the routes received in the RIP updates from R3 and list it on Question 3 Answer Sheet.

Step 3: Disable automatic summarization.

R1(config)# router rip

R1(config-router)# no auto-summary

b. Issue the clear ip route * command to clear the routing table.

R1(config-router)# end

R1# clear ip route *

c. Examine the routing tables. Remember that it will take some time to converge the routing tables after clearing them.

The LAN subnets connected to R1 and R3 should now be included in all three routing tables.

R2# show ip route

Gateway of last resort is not set

10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks

C 10.1.1.0/30 is directly connected, Serial0/0/0

L 10.1.1.2/32 is directly connected, Serial0/0/0

C 10.2.2.0/30 is directly connected, Serial0/0/1

L 10.2.2.2/32 is directly connected, Serial0/0/1

172.30.0.0/16 is variably subnetted, 3 subnets, 2 masks

R 172.30.0.0/16 [120/1] via 10.2.2.1, 00:01:01, Serial0/0/1

[120/1] via 10.1.1.1, 00:01:15, Serial0/0/0

R 172.30.10.0/24 [120/1] via 10.1.1.1, 00:00:21, Serial0/0/0

R 172.30.30.0/24 [120/1] via 10.2.2.1, 00:00:04, Serial0/0/1

209.165.201.0/24 is variably subnetted, 2 subnets, 2 masks

C 209.165.201.0/24 is directly connected, GigabitEthernet0/0

L 209.165.201.1/32 is directly connected, GigabitEthernet0/0

R1# show ip route

Gateway of last resort is not set

10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks

C 10.1.1.0/30 is directly connected, Serial0/0/0

L 10.1.1.1/32 is directly connected, Serial0/0/0

R 10.2.2.0/30 [120/1] via 10.1.1.2, 00:00:12, Serial0/0/0

172.30.0.0/16 is variably subnetted, 3 subnets, 2 masks

C 172.30.10.0/24 is directly connected, GigabitEthernet0/1

L 172.30.10.1/32 is directly connected, GigabitEthernet0/1

R 172.30.30.0/24 [120/2] via 10.1.1.2, 00:00:12, Serial0/0/0

R3# show ip route

10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks

C 10.2.2.0/30 is directly connected, Serial0/0/1

L 10.2.2.1/32 is directly connected, Serial0/0/1

R 10.1.1.0/30 [120/1] via 10.2.2.2, 00:00:23, Serial0/0/1

172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks

C 172.30.30.0/24 is directly connected, GigabitEthernet0/1

L 172.30.30.1/32 is directly connected, GigabitEthernet0/1

R 172.30.10.0 [120/2] via 10.2.2.2, 00:00:16, Serial0/0/1

d. Use the debug ip rip command on R2 to examine the RIP updates.

R2# debug ip rip

After 60 seconds, issue the no debug ip rip command.

Answer Questions 4 and 5 on the Answer Sheet.

Step 4: Configure and redistribute a default route for Internet access.

R2(config)# ip route 0.0.0.0 0.0.0.0 209.165.201.2

b. R2 will advertise a route to the other routers if the default-information originate command is added to its RIP configuration.

R2(config)# router rip

R2(config-router)# default-information originate

Step 5: Verify the routing configuration.

a. View the routing table on R1.

R1# show ip route

Gateway of last resort is 10.1.1.2 to network 0.0.0.0

R* 0.0.0.0/0 [120/1] via 10.1.1.2, 00:00:13, Serial0/0/0

10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks

C 10.1.1.0/30 is directly connected, Serial0/0/0

L 10.1.1.1/32 is directly connected, Serial0/0/0

R 10.2.2.0/30 [120/1] via 10.1.1.2, 00:00:13, Serial0/0/0

172.30.0.0/16 is variably subnetted, 3 subnets, 2 masks

C 172.30.10.0/24 is directly connected, GigabitEthernet0/1

L 172.30.10.1/32 is directly connected, GigabitEthernet0/1

R 172.30.30.0/24 [120/2] via 10.1.1.2, 00:00:13, Serial0/0/0

Answer Question 6 on the Answer Sheet.

b. View the routing table on R2.

Answer Question 7 on the Answer Sheet.

Step 6: Verify connectivity.

a. Simulate sending traffic to the Internet by pinging from PC-A and PC-C to 209.165.201.2.

Answer Question 8 on the Answer Sheet.

b. Verify that hosts within the subnetted network can reach each other by pinging between PC-A and PC-C.

Answer Question 9 on the Answer Sheet.

Note: It may be necessary to disable the PCs firewall.

Answer the Reflection Questions 1 and 2 , Paste R1, R2 and R3 Output onto the Answer Sheet.

__MACOSX/Lab10/._Lab 10 Instructions(1).docx
Lab10/Lab 10 Answer Sheet-PLo.docx
Liberty University

CSIS 331

Lab 10 Answer Sheet

Ping From Device

Ping to Device IP

Possible Y/N

Why?

PC-A

PC-B

PC-A

PC-C

PC-B

PC-C

PC-A

1. When issuing the debug ip rip command on R2, what information is provided that confirms RIPv2 is running?

2. When issuing the show run command on R3, what information is provided that confirms RIPv2 is running?

3. Use the debug ip rip command on R2 to determine the routes received in the RIP updates from R3 and list them here.

4. What is the route in the RIP updates that is received from R3?

5. Are the subnet masks included in the routing updates? __ Yes / __ No

6. How can you tell from the routing table that the subnetted network shared by R1 and R3 has a pathway for Internet traffic?

7. How is the pathway for Internet traffic provided in its routing table?

8. Were the pings successful?__ Yes / __ No

9. Were the pings successful?__ __ Yes / __ No

Reflection Questions 1: Why would you turn off automatic summarization for RIPv2?

Reflection Questions 2:How did R1 and R3learn the pathway to the Internet?

Copy and Paste R1 show run Output:

Copy and Paste R2 show run Output:

Copy and Paste R3 show run Output:

Our Service Charter

1. Professional & Expert Writers: Blackboard Experts only hires the best. Our writers are specially selected and recruited, after which they undergo further training to perfect their skills for specialization purposes. Moreover, our writers are holders of masters and Ph.D. degrees. They have impressive academic records, besides being native English speakers.

2. Top Quality Papers: Our customers are always guaranteed of papers that exceed their expectations. All our writers have +5 years of experience. This implies that all papers are written by individuals who are experts in their fields. In addition, the quality team reviews all the papers before sending them to the customers.

3. Plagiarism-Free Papers: All papers provided by Blackboard Experts are written from scratch. Appropriate referencing and citation of key information are followed. Plagiarism checkers are used by the Quality assurance team and our editors just to double-check that there are no instances of plagiarism.

4. Timely Delivery: Time wasted is equivalent to a failed dedication and commitment. Blackboard Experts is known for timely delivery of any pending customer orders. Customers are well informed of the progress of their papers to ensure they keep track of what the writer is providing before the final draft is sent for grading.

5. Affordable Prices: Our prices are fairly structured to fit in all groups. Any customer willing to place their assignments with us can do so at very affordable prices. In addition, our customers enjoy regular discounts and bonuses.

6. 24/7 Customer Support: At Blackboard Experts, we have put in place a team of experts who answer to all customer inquiries promptly. The best part is the ever-availability of the team. Customers can make inquiries anytime.

Cisco Packet Tracer

Cisco Packet Tracer

Our Service Charter

Recent Posts

Recent Comments